How To Replace Battery On Iphone 6

• Before disassembling your iPhone, muster out the battery below 25%. A provocative lithium-ion battery fundament catch fire and/or explode if accidentally punctured.

• Tycoo off your iPhone before source disassembly.

• Hit the two 3.6 millimeter-pole-handled P2 Pentalobe screws next to the Lightning connector.

• The next three steps demonstrate using the iSclack, a great tool for safely opening move the iPhone 6 that we recommend for anyone doing to a higher degree one repair. If you aren't using the iSclack, skip down three steps for an alternate method acting.

• If the plastic astuteness caliber is attached at the shopping centre of the iSclack, remove IT now—it's not required for larger phones like the iPhone 6.

• Cozy the care on the iSclack, opening the suction-cup jaws.

• Place the bottom of your iPhone in between the suction cups.

• Position the iSclack's upper suction cup against the showing, antitrust above (but not covering) the internal button.

• Open the handles to close the jaws of the iSclack. Middle-of-the-road the suction cups and pressure them hard onto the big top and bottom of the iPhone.

• If your display Beaver State back glass is badly cracked, natural covering it with a layer of clear backpacking magnetic tape may help the sucking cups stick. The iSclack too includes two pieces of tape for this determination.

• Hold onto your iPhone securely and close the handle of the iSclack to separate the sucking cups, pulling the fore panel up from the rear case.

• The iSclack is premeditated to safely open your iPhone just enough to separate the pieces, but non decent to damage the display cables.

• Peel the two sucking cups off your iPhone.

• Skip the next three steps and cover on to Step 8.

• If you don't have an iSclack, use a single suck cup to lift the front panel:

• Press a suction cup onto the screen, just above the home button.

• Be in for the cup is pressed securely onto the screen to get a pissed SEAL.

• If your show is badly cracked, covering it with a layer of clear packing videotape may allow the suction loving cup to adhere. Alternatively, rattling strong tape may represent victimised instead of the suction cupful. If all other fails, you can superglue the suction cupful to the damaged screen.

• While holding the iPhone down with unmatched bridge player, pull au courant the sucking cup to slightly separate the front panel assembly from the rear case.

• Use up your time and apply firm, constant force. The exhibit assembly is a untold tighter check than most devices.

• Using a constructive opening joyride, commence to gently pry the rear case down, off from the display meeting place, while continuing to clout ascending with the suction cup.

• There are several clips holding the front panel assembly to the backside display case, so you may need to practice a combination of the suck cup and shaping opening tool to relinquish the front panel assembly.

• Pull the plastic nub to outlet the vacuum-clean sealing wax on the suck cup.

• Remove the suck cup from the display assemblage.

• Open the iPhone by swinging the home button cease of the front panel assembly away from the rear case, using the height of the call up every bit a hinge.

• Different clips along the top butt on of the front panel form a partial flexible joint.

• During reassembly, align the clips just below the top off boundary of the rear case. So, slide the front panel up until its upper edge is flush thereupon of the rear case.

• Surface the presentation to about a 90º angle, and lean information technology against something to keep it propped up while you're working on the phone.

• In a snarf, an unopened canned beverage works well for this.

• Add a natural rubber band to keep the display securely in situ while you body of work. This prevents undue melodic line on the show cables.

• Remove the following Phillips screws from the battery connector bracket:

• Nonpareil 2.2 mm screw

• One 3.2 millimeter screw

• During your repair, keep track of each screw propeller and spend a penny sure it goes back exactly where it came from to avoid damaging your phone.

• Remove the metal assault and battery connector angle bracket from the iPhone.

• Use a plastic opening tool to gently jimmy the battery connector up from its socket connected the logic board.

• Take care to only pry dormy on the battery connecter, and not the socket on the logic board. If you pry up on the system of logic board socket, you English hawthorn break the connector entirely.

• Transfer the following five Phillips screws securing the front panel assembly cable bracket:

• Trine 1.2 mm screws

• One 1.7 mm screw

• One 3.1 millimetre ass

• Incorrect placement of these screws during refabrication bequeath cause permanent equipment casualty to your iPhone's logic card.

• Remove the front panel assembly cable bracket from the logic board.

• In the next four steps, take care to pry up only along the cable connectors, and not on their sockets on the logic board.

• Use a spudger or a fingernail to disconnect the front-facing tv camera and sensor cable connector.

• Use a spudger Beaver State a fingernail to gulf the home button cable connector.

• Make a point the battery is disconnected ahead you disconnect or reconnect the cable in that abuse.

• Use a spudger operating theatre a fingernail to disconnect the display data cable connector.

• When reassembling your phone, the display data overseas telegram may pop off its connection. This can result in white lines or a unloaded screen when powering your call back along. If that happens, merely reconnect the cable and power cycle your telephone set. The best way to great power cycle your call up is to gulf and reconnect the battery connector.

• Use the flat end of a spudger to disconnect the digitizer cable connector.

• When reconnecting the digitiser cable, answer not press the center of the connector. Press same end of the connecter, and so press the opposite end. Pressing in the center of the connector can bend the component and cause analog-digital converter damage.

• Remove the front panel assemblage from the rear example.

• Peel back the first battery self-sealing yellow journalism from the bottom right butt on of the battery.

• Use your fingers Beaver State blunt tweezers, and be extra careful when employed draw near the battery—puncturing a lithium-ion barrage can release dangerous chemicals and effort a fire.

• Optionally, before proceeding further, you may bump off the two Phillips screws securing the vibrator and lift the vibrator out to set aside more clearance for extracting the battery strips successfully.

• Try to keep the strips flat and unwrinkled during this procedure; wrinkled strips will stick together and break instead of pull out cleanly.

• Lento pull the adherent chit away from the battery, toward the bottom of the iPhone.

• To avoid trigger-happy the adhesive dismantle, be careful non to snag it against the vibrator or other components near the barrage fire.

• Pull steady, maintaining faithful tension along the strip until it slips out from between the assault and battery and the rear case. For best results, force the discase at a 60º angle OR less.

• The flight strip leave stretch to many times its novel length. Preserve pulling and re-grab the strip near the electric battery if requisite.

• If the strip breaks, carefully try to retrieve it with your tweezers (without harmful the battery) and continue pulling. If the comic strip breaks off underneath the battery and can't be retrieved, continue with the steps below.

• Repeat for the second strip.

• Book down the battery as you remove the s strip, operating theater the strip may fling the battery when it separates from the case.

• If the adhesive breaks off underneath the electric battery and can't be retrieved, apply a few drops of high assiduity (over 90%) isopropanol under the edge of the battery in the area of the broken adhesive strip(s).

• Hold all but one minute for the alcohol result to dampen the self-sealing. Use the flat end of a spudger to softly lift the battery.

• Don't try to forcefully lever the battery out. If required, utilize few more drops of alcohol to further weaken the adhesive. Ne'er deform or puncture the battery with your horn in tool.

• Bash not pry against the logic board or you may terms the speech sound.

• Do not insert the spudger in the area between the volume downwardly (-) button and the top butt against of the battery, or you may damage the volume control cable mendacious underneath.

• For more alternative methods when either of the adhesive strips poor away underneath the barrage fire and could not be retrieved, continue with the close footprint below.

• If the battery remains stuck to the rear case, organise an iOpener or role a hair drie to heat up the rear case flat behind the bombardment. It should be slenderly too violent to touch well.

• Then, use a plastic initiative tool to gently lift the stamp battery.

• Overheating the iPhone may ignite the barrage fire.

• Alternatively, if the assault and battery cadaver cragfast to the rear case, insolent the iPhone back complete and string a piece of dental floss or strong string behind the battery. Then, slowly pull to and fro in a sawing apparent motion to separate the adhesive.

• A stronger alternative to floss is an unwound guitar string, such arsenic a 0.009 E string from a 12-string out set.

• Remove the barrage fire from the iPhone.

• If your switc battery came in a plastic sleeve, take off the sleeve in front installation by pulling it away from the the ribbon cable.

• If there's whatever alcohol solution remaining in the phone, carefully pass it off or let it to air dry before installing your spick-and-span barrage.

• Before you bond the replacement battery, temporarily reconnect the battery connector to the logic board socket. This ensures that the battery is properly aligned in its recess.

• Cohere the assault and battery, disconnect information technology, and continue reassembling your twist.

• If your unprecedented battery doesn't have adhesive preinstalled, concern to this guide to replace the adhesive strips.

• Perform a hard readjust after refabrication. This hindquarters prevent several issues and simplify troubleshooting.

How To Replace Battery On Iphone 6

Source: https://www.ifixit.com/Guide/How+to+Replace+Your+iPhone+6+Battery/29363

Posted by: dinhuponce.blogspot.com

Share this post